Wood CalculatorMeasure, plan & work with wood

Wood calculators / Workshop geometry

Measure the wood. State the basis.

Wood Stair Geometry Calculator

Calculate an explicit equal-rise stair geometry and ideal slope line.

Your wood & project inputs

m
mm
mm

Starting values are calculation examples. Verify actual dimensions, moisture basis, rates and model assumptions. Dimension-unit switching does not change fixed-unit price or engineering-property inputs.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Risers = ceil(total rise/chosen maximum riser); equal riser = rise/count; treads = risers−1.

Calculate an explicit equal-rise stair geometry and ideal slope line.

  1. Confirm the physical, product or tally basis and use the stated units.
  2. Enter actual measurements and justified properties, prices or project allowances.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Not a code-compliant stair or notched-stringer strength design. Landings, headroom, nosing, finish thickness and bearing details are excluded.

Wood Stair Geometry: formula, units and interpretation

Calculate an explicit equal-rise stair geometry and ideal slope line. Not a code-compliant stair or notched-stringer strength design. Landings, headroom, nosing, finish thickness and bearing details are excluded.

Separate the measured physical quantity from the purchase or design convention. Nominal lumber names, finished dimensions, geometric board feet, log-rule yield, stacked cords and mass describe different things. The method on this page uses only the basis stated beside its inputs; do not replace a missing property with an unrelated unit or trade name.

Before using the answer for a real project, confirm measurements and the relevant supplier information. Entered waste, prices, material properties and limits remain user choices. A rounded purchasing count is a quantity allowance rather than a cutting plan, and a calculated physical response is not a building-code approval.

Check the numbers

Wood Stair Geometry Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not stock recommendations, current quotes, code design values or full standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Total floor-to-floor rise = 2.8 m; Chosen maximum equal riser = 180 mm; Chosen horizontal tread going = 250 mm.

OutputComputed result
Equal-rise stair geometry16 risers
Actual riser175 mm
Tread count15 treads
Total horizontal going3.75 m
Ideal slope-line length4.680011 m
Slope angle36.747471 degrees

How the stated input changes the result

ScenarioChanged input / basisResult
1.4 mTotal floor-to-floor rise8 risers
2.1 mTotal floor-to-floor rise12 risers
2.8 mTotal floor-to-floor rise16 risers
3.5 mTotal floor-to-floor rise20 risers
4.2 mTotal floor-to-floor rise24 risers
5.6 mTotal floor-to-floor rise32 risers

Unchanged inputs use: Dimension units = Metric (m / mm); Total floor-to-floor rise = 2.8 m; Chosen maximum equal riser = 180 mm; Chosen horizontal tread going = 250 mm. Results retain the model limitations described above.

Common questions

Why is the tread count one less than risers?

This model uses the upper floor as the final landing, rather than adding another separate tread at that elevation.

Is the target riser a legal requirement?

No. Supply and verify the applicable project criteria independently.

Does slope-line length determine a safe stringer?

No. Member size and notch effects require separate structural assessment.

How do I use this wood stair geometry calculator?

Calculate an explicit equal-rise stair geometry and ideal slope line. Risers = ceil(total rise/chosen maximum riser); equal riser = rise/count; treads = risers−1. Read the dimensioned examples below before entering project values.

Do starting values represent product or code recommendations?

No. They are stated calculation examples. Verify actual dimensions, material or product properties, units and site conditions. Neither a positive result nor an example value establishes a certified product, allowed load, compliant layout or current market price.

Can I export the result to Excel?

After calculating, use Export CSV. Excel can open the numeric results and submitted inputs. This is a text export, not a native formula workbook, desktop app or downloadable design package.

Where do the formulas and data come from?

Method and material references are listed below as plain-text addresses. Dimensional tables are calculated here from the stated inputs. Product density examples retain their species, moisture or manufacturer basis. Sources are not fetched when you use the calculator.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • NIST SP 811, Appendix B.9: mass, length, area and volume conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9
  • NIST PS 20-25 American Softwood Lumber Standard, section 2.16 and Table 3 (printed page 15)https://www.nist.gov/system/files/documents/2024/12/11/PS%2020-25%20Final.pdf