Wood CalculatorMeasure, plan & work with wood

Wood calculators / Workshop geometry

Measure the wood. State the basis.

Wood CNC Feed Calculator

Relate stated spindle speed, cutting-edge count, feed and chip load for CNC wood routing.

Your wood & project inputs

RPM
edges
mm

Starting values are calculation examples. Verify actual dimensions, moisture basis, rates and model assumptions. Dimension-unit switching does not change fixed-unit price or engineering-property inputs.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Feed = RPM × effective cutting edges × chip load; rearrange for the selected output.

Relate stated spindle speed, cutting-edge count, feed and chip load for CNC wood routing.

  1. Confirm the physical, product or tally basis and use the stated units.
  2. Enter actual measurements and justified properties, prices or project allowances.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Example inputs are not recommended cutter settings. Tool diameter, material, engagement, runout, machine limits and manufacturer data remain essential.

Wood CNC Feed: formula, units and interpretation

Relate stated spindle speed, cutting-edge count, feed and chip load for CNC wood routing. Example inputs are not recommended cutter settings. Tool diameter, material, engagement, runout, machine limits and manufacturer data remain essential.

Separate the measured physical quantity from the purchase or design convention. Nominal lumber names, finished dimensions, geometric board feet, log-rule yield, stacked cords and mass describe different things. The method on this page uses only the basis stated beside its inputs; do not replace a missing property with an unrelated unit or trade name.

Before using the answer for a real project, confirm measurements and the relevant supplier information. Entered waste, prices, material properties and limits remain user choices. A rounded purchasing count is a quantity allowance rather than a cutting plan, and a calculated physical response is not a building-code approval.

Check the numbers

Wood CNC Feed Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not stock recommendations, current quotes, code design values or full standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Spindle speed = 18000 RPM; Effective cutting edges = 2 edges; Chosen chip load = 0.15 mm.

OutputComputed result
Feed at supplied chip load5,400 mm/min
Feed in inches per minute212.598425 in/min

How the stated input changes the result

ScenarioChanged input / basisResult
9000 RPMSpindle speed2,700 mm/min
13500 RPMSpindle speed4,050 mm/min
18000 RPMSpindle speed5,400 mm/min
22500 RPMSpindle speed6,750 mm/min
27000 RPMSpindle speed8,100 mm/min
36000 RPMSpindle speed10,800 mm/min

Unchanged inputs use: Dimension units = Metric (m / mm); Spindle speed = 18000 RPM; Effective cutting edges = 2 edges; Chosen chip load = 0.15 mm. Results retain the model limitations described above.

Common questions

Does this choose the best feed and speed?

No. It evaluates or rearranges the entered chip-load relationship.

Why use effective cutting edges?

Only engaged cutting edges contribute as assumed by the feed-per-tooth relation.

Can I use it for MDF or plywood?

The arithmetic can apply, but the chosen settings must come from the relevant tooling/material conditions.

How do I use this wood cnc feed calculator?

Relate stated spindle speed, cutting-edge count, feed and chip load for CNC wood routing. Feed = RPM × effective cutting edges × chip load; rearrange for the selected output. Read the dimensioned examples below before entering project values.

Do starting values represent product or code recommendations?

No. They are stated calculation examples. Verify actual dimensions, material or product properties, units and site conditions. Neither a positive result nor an example value establishes a certified product, allowed load, compliant layout or current market price.

Can I export the result to Excel?

After calculating, use Export CSV. Excel can open the numeric results and submitted inputs. This is a text export, not a native formula workbook, desktop app or downloadable design package.

Where do the formulas and data come from?

Method and material references are listed below as plain-text addresses. Dimensional tables are calculated here from the stated inputs. Product density examples retain their species, moisture or manufacturer basis. Sources are not fetched when you use the calculator.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • LMT Onsrud, Hard Wood Cutting Data Recommendations, formula block on printed page 115https://onsrud.com/images/Hard%20Wood.pdf
  • LMT Onsrud: Cutting Data Recommendations, hardwood/softwood/MDF/plywood resourceshttps://onsrud.com/Forms/Cutting-Data-Recommendations.asp
  • NIST SP 811, Appendix B.9: mass, length, area and volume conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9