Wood CalculatorMeasure, plan & work with wood

Wood calculators / Panels & cutting

Measure the wood. State the basis.

Plywood Sheet Cut List Calculator

Generate a bounded rectangular sheet-cut estimate and schematic for up to 200 parts.

Your wood & project inputs

mm
mm
mm

Cut dimensions follow the selected mm / in units; counts stay whole numbers.

Starting values are calculation examples. Verify actual dimensions, moisture basis, rates and model assumptions. Dimension-unit switching does not change fixed-unit price or engineering-property inputs.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Sort rectangles by area; greedily place into guillotine-split free rectangles, testing permitted 90° rotation and the stated inter-part kerf.

Generate a bounded rectangular sheet-cut estimate and schematic for up to 200 parts.

  1. Confirm the physical, product or tally basis and use the stated units.
  2. Enter actual measurements and justified properties, prices or project allowances.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Heuristic layout only, not optimal nesting or a safe machining sequence. Rotation is optional because face grain and finish can matter. The first eight sheet schematics are shown.

Plywood Sheet Cut List: formula, units and interpretation

Generate a bounded rectangular sheet-cut estimate and schematic for up to 200 parts. Heuristic layout only, not optimal nesting or a safe machining sequence. Rotation is optional because face grain and finish can matter. The first eight sheet schematics are shown.

Separate the measured physical quantity from the purchase or design convention. Nominal lumber names, finished dimensions, geometric board feet, log-rule yield, stacked cords and mass describe different things. The method on this page uses only the basis stated beside its inputs; do not replace a missing property with an unrelated unit or trade name.

Before using the answer for a real project, confirm measurements and the relevant supplier information. Entered waste, prices, material properties and limits remain user choices. A rounded purchasing count is a quantity allowance rather than a cutting plan, and a calculated physical response is not a building-code approval.

Check the numbers

Plywood Sheet Cut List Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not stock recommendations, current quotes, code design values or full standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Actual sheet width = 1220 mm; Actual sheet length = 2440 mm; Inter-part saw kerf = 3 mm; Allow 90-degree part rotation = Yes, when grain / finish allows; Cut list: width, length, quantity (one per line) = 600,800,2 400,500,3.

OutputComputed result
Greedy guillotine cut-plan estimate1 sheets
Rectangles5 pieces
Part area1.56 m²
Sheet area purchased2.9768 m²
Unassigned area including kerfs1.4168 m²
Sheet 1 / part 1600 × 800 at (0, 0) mm
Sheet 1 / part 2600 × 800 at (603, 0) mm
Sheet 1 / part 3400 × 500 at (0, 803) mm
Sheet 1 / part 4400 × 500 at (403, 803) mm
Sheet 1 / part 5400 × 500 at (806, 803) mm

How the stated input changes the result

ScenarioChanged input / basisResult
610 mmActual sheet width2 sheets
793 mmActual sheet width2 sheets
976 mmActual sheet width2 sheets
1220 mmActual sheet width1 sheets
1525 mmActual sheet width1 sheets
1830 mmActual sheet width1 sheets

Unchanged inputs use: Dimension units = Metric (m / mm); Actual sheet width = 1220 mm; Actual sheet length = 2440 mm; Inter-part saw kerf = 3 mm; Allow 90-degree part rotation = Yes, when grain / finish allows; Cut list: width, length, quantity (one per line) = 600,800,2 400,500,3. Results retain the model limitations described above.

Common questions

Is this a full cabinet or wardrobe design tool?

No. Supply the actual rectangular part list, including any separately determined joints and allowances.

Does it support arbitrary shapes?

No. Rectangles only; no grain matching, defects, edge banding or curved nesting.

What does the diagram show?

The returned rectangle placements on the selected sheet dimensions. It is a schematic, not a scaled print cutting template.

Can the number of sheets exceed the area lower bound?

Yes. Geometry, kerf, rotation constraints and the heuristic can require more sheets than total area alone suggests.

How do I use this plywood sheet cut list calculator?

Generate a bounded rectangular sheet-cut estimate and schematic for up to 200 parts. Sort rectangles by area; greedily place into guillotine-split free rectangles, testing permitted 90° rotation and the stated inter-part kerf. Read the dimensioned examples below before entering project values.

Do starting values represent product or code recommendations?

No. They are stated calculation examples. Verify actual dimensions, material or product properties, units and site conditions. Neither a positive result nor an example value establishes a certified product, allowed load, compliant layout or current market price.

Can I export the result to Excel?

After calculating, use Export CSV. Excel can open the numeric results and submitted inputs. This is a text export, not a native formula workbook, desktop app or downloadable design package.

Where do the formulas and data come from?

Method and material references are listed below as plain-text addresses. Dimensional tables are calculated here from the stated inputs. Product density examples retain their species, moisture or manufacturer basis. Sources are not fetched when you use the calculator.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • Google OR-Tools: bin-packing problem definition; this site uses its own disclosed heuristic, not the OR-Tools solverhttps://developers.google.com/optimization/pack/bin_packing
  • NIST SP 811, Appendix B.9: mass, length, area and volume conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9