Wood calculators / Workshop geometry
Measure the wood. State the basis.
Wood Chip Load Calculator
Relate stated spindle speed, cutting-edge count, feed and chip load for CNC wood routing.
Your wood & project inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Feed = RPM × effective cutting edges × chip load; rearrange for the selected output.
Relate stated spindle speed, cutting-edge count, feed and chip load for CNC wood routing.
- Confirm the physical, product or tally basis and use the stated units.
- Enter actual measurements and justified properties, prices or project allowances.
- Submit the form, then interpret the result with the assumptions and limits below.
Example inputs are not recommended cutter settings. Tool diameter, material, engagement, runout, machine limits and manufacturer data remain essential.
Wood Chip Load: formula, units and interpretation
Relate stated spindle speed, cutting-edge count, feed and chip load for CNC wood routing. Example inputs are not recommended cutter settings. Tool diameter, material, engagement, runout, machine limits and manufacturer data remain essential.
Separate the measured physical quantity from the purchase or design convention. Nominal lumber names, finished dimensions, geometric board feet, log-rule yield, stacked cords and mass describe different things. The method on this page uses only the basis stated beside its inputs; do not replace a missing property with an unrelated unit or trade name.
Before using the answer for a real project, confirm measurements and the relevant supplier information. Entered waste, prices, material properties and limits remain user choices. A rounded purchasing count is a quantity allowance rather than a cutting plan, and a calculated physical response is not a building-code approval.
Continue with: Wood Stair Geometry Calculator · Wood Miter Angle Calculator · Wood Right Triangle Cut Angle Calculator · Wood CNC Feed Calculator
Check the numbers
Wood Chip Load Calculator: calculated examples
These scenarios are computed with the same method as the form. They are not stock recommendations, current quotes, code design values or full standards tables.
Worked example with stated inputs
Dimension units = Metric (m / mm); Spindle speed = 18000 RPM; Effective cutting edges = 2 edges; Programmed linear feed = 3000 mm/min.
| Output | Computed result |
|---|---|
| Chip load from stated feed and speed | 0.083333 mm/tooth |
How the stated input changes the result
| Scenario | Changed input / basis | Result |
|---|---|---|
| 9000 RPM | Spindle speed | 0.166667 mm/tooth |
| 13500 RPM | Spindle speed | 0.111111 mm/tooth |
| 18000 RPM | Spindle speed | 0.083333 mm/tooth |
| 22500 RPM | Spindle speed | 0.066667 mm/tooth |
| 27000 RPM | Spindle speed | 0.055556 mm/tooth |
| 36000 RPM | Spindle speed | 0.041667 mm/tooth |
Unchanged inputs use: Dimension units = Metric (m / mm); Spindle speed = 18000 RPM; Effective cutting edges = 2 edges; Programmed linear feed = 3000 mm/min. Results retain the model limitations described above.
Common questions
Does this choose the best feed and speed?
No. It evaluates or rearranges the entered chip-load relationship.
Why use effective cutting edges?
Only engaged cutting edges contribute as assumed by the feed-per-tooth relation.
Can I use it for MDF or plywood?
The arithmetic can apply, but the chosen settings must come from the relevant tooling/material conditions.
How do I use this wood chip load calculator?
Relate stated spindle speed, cutting-edge count, feed and chip load for CNC wood routing. Feed = RPM × effective cutting edges × chip load; rearrange for the selected output. Read the dimensioned examples below before entering project values.
Do starting values represent product or code recommendations?
No. They are stated calculation examples. Verify actual dimensions, material or product properties, units and site conditions. Neither a positive result nor an example value establishes a certified product, allowed load, compliant layout or current market price.
Can I export the result to Excel?
After calculating, use Export CSV. Excel can open the numeric results and submitted inputs. This is a text export, not a native formula workbook, desktop app or downloadable design package.
Where do the formulas and data come from?
Method and material references are listed below as plain-text addresses. Dimensional tables are calculated here from the stated inputs. Product density examples retain their species, moisture or manufacturer basis. Sources are not fetched when you use the calculator.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.
- LMT Onsrud, Hard Wood Cutting Data Recommendations, formula block on printed page 115https://onsrud.com/images/Hard%20Wood.pdf
- LMT Onsrud: Cutting Data Recommendations, hardwood/softwood/MDF/plywood resourceshttps://onsrud.com/Forms/Cutting-Data-Recommendations.asp
- NIST SP 811, Appendix B.9: mass, length, area and volume conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9