Wood CalculatorMeasure, plan & work with wood

Wood calculators / Workshop geometry

Measure the wood. State the basis.

Wood Cutting Cost Scenario Calculator

Estimate continuous-cut time and an entered-rate workshop charge.

Your wood & project inputs

m
m/min

Starting values are calculation examples. Verify actual dimensions, moisture basis, rates and model assumptions. Dimension-unit switching does not change fixed-unit price or engineering-property inputs.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Ideal cutting time = path length / entered average cutting feed; price scenario = time × entered rate + setup.

Estimate continuous-cut time and an entered-rate workshop charge.

  1. Confirm the physical, product or tally basis and use the stated units.
  2. Enter actual measurements and justified properties, prices or project allowances.
  3. Submit the form, then interpret the result with the assumptions and limits below.

No acceleration, pierces, tool changes, laser physics, quote lookup or material cost unless separately included in your inputs. Imperial feed is entered in ft/min.

Wood Cutting Cost Scenario: formula, units and interpretation

Estimate continuous-cut time and an entered-rate workshop charge. No acceleration, pierces, tool changes, laser physics, quote lookup or material cost unless separately included in your inputs. Imperial feed is entered in ft/min.

Separate the measured physical quantity from the purchase or design convention. Nominal lumber names, finished dimensions, geometric board feet, log-rule yield, stacked cords and mass describe different things. The method on this page uses only the basis stated beside its inputs; do not replace a missing property with an unrelated unit or trade name.

Before using the answer for a real project, confirm measurements and the relevant supplier information. Entered waste, prices, material properties and limits remain user choices. A rounded purchasing count is a quantity allowance rather than a cutting plan, and a calculated physical response is not a building-code approval.

Check the numbers

Wood Cutting Cost Scenario Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not stock recommendations, current quotes, code design values or full standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Programmed continuous cutting distance = 20 m; Average actual cutting feed = 3 m/min; Entered machine / shop rate per minute = 1 ; Entered setup charge = 10 ; Currency label = USD.

OutputComputed result
Entered-rate machining budget16.666667 USD
Ideal continuous cutting time6.666667 min

How the stated input changes the result

ScenarioChanged input / basisResult
10 mProgrammed continuous cutting distance13.333333 USD
15 mProgrammed continuous cutting distance15 USD
20 mProgrammed continuous cutting distance16.666667 USD
25 mProgrammed continuous cutting distance18.333333 USD
30 mProgrammed continuous cutting distance20 USD
40 mProgrammed continuous cutting distance23.333333 USD

Unchanged inputs use: Dimension units = Metric (m / mm); Programmed continuous cutting distance = 20 m; Average actual cutting feed = 3 m/min; Entered machine / shop rate per minute = 1 ; Entered setup charge = 10 ; Currency label = USD. Results retain the model limitations described above.

Common questions

Is programmed feed always achieved?

No. Use a representative actual average or account for motion losses separately.

Does it work for a laser quote?

Only as time/rate arithmetic if appropriate path speed and charges are supplied; no laser process model is included.

Are workshop prices current?

No. All rates and charges are user inputs.

How do I use this wood cutting cost scenario calculator?

Estimate continuous-cut time and an entered-rate workshop charge. Ideal cutting time = path length / entered average cutting feed; price scenario = time × entered rate + setup. Read the dimensioned examples below before entering project values.

Do starting values represent product or code recommendations?

No. They are stated calculation examples. Verify actual dimensions, material or product properties, units and site conditions. Neither a positive result nor an example value establishes a certified product, allowed load, compliant layout or current market price.

Can I export the result to Excel?

After calculating, use Export CSV. Excel can open the numeric results and submitted inputs. This is a text export, not a native formula workbook, desktop app or downloadable design package.

Where do the formulas and data come from?

Method and material references are listed below as plain-text addresses. Dimensional tables are calculated here from the stated inputs. Product density examples retain their species, moisture or manufacturer basis. Sources are not fetched when you use the calculator.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • LMT Onsrud, Hard Wood Cutting Data Recommendations, formula block on printed page 115https://onsrud.com/images/Hard%20Wood.pdf
  • NIST SP 811, Appendix B.9: mass, length, area and volume conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9