Wood CalculatorMeasure, plan & work with wood

Wood calculators / Firewood & heating

Measure the wood. State the basis.

Solid Wood to Cords Calculator

Estimate stacked cords from solid wood volume only when a valid stacking fraction is supplied.

Your wood & project inputs

m³
ratio

Starting values are calculation examples. Verify actual dimensions, moisture basis, rates and model assumptions. Dimension-unit switching does not change fixed-unit price or engineering-property inputs.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Stacked volume = solid volume / supplied solid fraction; cords = stacked volume/128 ft³.

Estimate stacked cords from solid wood volume only when a valid stacking fraction is supplied.

  1. Confirm the physical, product or tally basis and use the stated units.
  2. Enter actual measurements and justified properties, prices or project allowances.
  3. Submit the form, then interpret the result with the assumptions and limits below.

The initial 0.65 fraction is an illustration, not a universal conversion or a tree-to-firewood yield factor.

Solid Wood to Cords: formula, units and interpretation

Estimate stacked cords from solid wood volume only when a valid stacking fraction is supplied. The initial 0.65 fraction is an illustration, not a universal conversion or a tree-to-firewood yield factor.

Separate the measured physical quantity from the purchase or design convention. Nominal lumber names, finished dimensions, geometric board feet, log-rule yield, stacked cords and mass describe different things. The method on this page uses only the basis stated beside its inputs; do not replace a missing property with an unrelated unit or trade name.

Before using the answer for a real project, confirm measurements and the relevant supplier information. Entered waste, prices, material properties and limits remain user choices. A rounded purchasing count is a quantity allowance rather than a cutting plan, and a calculated physical response is not a building-code approval.

Check the numbers

Solid Wood to Cords Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not stock recommendations, current quotes, code design values or full standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Known solid wood volume = 2 m³; Measured / chosen solid fraction of stack = 0.65 ratio.

OutputComputed result
Cord estimate at supplied solid fraction0.84891 cords
Solid fraction0.65 ratio
Estimated stacked volume3.076923 m³

How the stated input changes the result

ScenarioChanged input / basisResult
1 m³Known solid wood volume0.424455 cords
1.5 m³Known solid wood volume0.636683 cords
2 m³Known solid wood volume0.84891 cords
2.5 m³Known solid wood volume1.061138 cords
3 m³Known solid wood volume1.273365 cords
4 m³Known solid wood volume1.697821 cords

Unchanged inputs use: Dimension units = Metric (m / mm); Known solid wood volume = 2 m³; Measured / chosen solid fraction of stack = 0.65 ratio. Results retain the model limitations described above.

Common questions

Why is a solid fraction needed?

Stacked firewood includes gaps. The proportion depends on piece shape and stacking.

Can I apply it to an entire standing tree?

Not without a separate valid estimate of recoverable usable solid firewood.

Is the result a legal sale measurement?

Use actual measurement and applicable local requirements; this scenario does not certify a sale quantity.

How do I use this solid wood to cords calculator?

Estimate stacked cords from solid wood volume only when a valid stacking fraction is supplied. Stacked volume = solid volume / supplied solid fraction; cords = stacked volume/128 ft³. Read the dimensioned examples below before entering project values.

Do starting values represent product or code recommendations?

No. They are stated calculation examples. Verify actual dimensions, material or product properties, units and site conditions. Neither a positive result nor an example value establishes a certified product, allowed load, compliant layout or current market price.

Can I export the result to Excel?

After calculating, use Export CSV. Excel can open the numeric results and submitted inputs. This is a text export, not a native formula workbook, desktop app or downloadable design package.

Where do the formulas and data come from?

Method and material references are listed below as plain-text addresses. Dimensional tables are calculated here from the stated inputs. Product density examples retain their species, moisture or manufacturer basis. Sources are not fetched when you use the calculator.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • NIST / NCWM, Avoid Getting Burned When Buying Firewood: cord measurementhttps://www.nist.gov/document/ncwm-firewood-factspdf
  • Measurement Canada: measuring bulk firewoodhttps://ised-isde.canada.ca/site/measurement-canada/en/infographics/measuring-bulk-firewood
  • NIST SP 811, Appendix B.9: mass, length, area and volume conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9