Wood CalculatorMeasure, plan & work with wood

Wood calculators / Workshop geometry

Measure the wood. State the basis.

Kerf Bending Arc Geometry Calculator

Compare ideal inner and outer circular arc lengths before assessing a bent-panel project.

Your wood & project inputs

m
mm
degrees

Starting values are calculation examples. Verify actual dimensions, moisture basis, rates and model assumptions. Dimension-unit switching does not change fixed-unit price or engineering-property inputs.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Inner arc = inside radius × angle(radians); outer arc = (inside radius + thickness) × angle(radians).

Compare ideal inner and outer circular arc lengths before assessing a bent-panel project.

  1. Confirm the physical, product or tally basis and use the stated units.
  2. Enter actual measurements and justified properties, prices or project allowances.
  3. Submit the form, then interpret the result with the assumptions and limits below.

This is arc geometry only. It does not determine safe kerf depth, kerf spacing, remaining web, bending strength or a plywood manufacturer’s bending limit.

Kerf Bending Arc Geometry: formula, units and interpretation

Compare ideal inner and outer circular arc lengths before assessing a bent-panel project. This is arc geometry only. It does not determine safe kerf depth, kerf spacing, remaining web, bending strength or a plywood manufacturer’s bending limit.

Separate the measured physical quantity from the purchase or design convention. Nominal lumber names, finished dimensions, geometric board feet, log-rule yield, stacked cords and mass describe different things. The method on this page uses only the basis stated beside its inputs; do not replace a missing property with an unrelated unit or trade name.

Before using the answer for a real project, confirm measurements and the relevant supplier information. Entered waste, prices, material properties and limits remain user choices. A rounded purchasing count is a quantity allowance rather than a cutting plan, and a calculated physical response is not a building-code approval.

Check the numbers

Kerf Bending Arc Geometry Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not stock recommendations, current quotes, code design values or full standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Desired inner arc radius = 0.3 m; Panel thickness = 12 mm; Desired circular arc angle = 90 degrees.

OutputComputed result
Outer-surface arc length0.490088 m
Inner-surface arc length0.471239 m
Difference between surface arcs0.01885 m
Arc angle90 degrees

How the stated input changes the result

ScenarioChanged input / basisResult
0.15 mDesired inner arc radius0.254469 m
0.225 mDesired inner arc radius0.372279 m
0.3 mDesired inner arc radius0.490088 m
0.375 mDesired inner arc radius0.607898 m
0.45 mDesired inner arc radius0.725708 m
0.6 mDesired inner arc radius0.961327 m

Unchanged inputs use: Dimension units = Metric (m / mm); Desired inner arc radius = 0.3 m; Panel thickness = 12 mm; Desired circular arc angle = 90 degrees. Results retain the model limitations described above.

Common questions

Does it give kerf spacing for bending wood?

No. A difference in arc lengths does not determine a safe cut pattern or material strain.

Is the radius measured at the neutral axis?

No. The input is explicitly the inner surface radius; the outer radius adds the full panel thickness.

Can it certify a bent plywood part?

No. Species, veneer orientation, adhesive, thickness and remaining web need appropriate product and process information.

How do I use this kerf bending arc geometry calculator?

Compare ideal inner and outer circular arc lengths before assessing a bent-panel project. Inner arc = inside radius × angle(radians); outer arc = (inside radius + thickness) × angle(radians). Read the dimensioned examples below before entering project values.

Do starting values represent product or code recommendations?

No. They are stated calculation examples. Verify actual dimensions, material or product properties, units and site conditions. Neither a positive result nor an example value establishes a certified product, allowed load, compliant layout or current market price.

Can I export the result to Excel?

After calculating, use Export CSV. Excel can open the numeric results and submitted inputs. This is a text export, not a native formula workbook, desktop app or downloadable design package.

Where do the formulas and data come from?

Method and material references are listed below as plain-text addresses. Dimensional tables are calculated here from the stated inputs. Product density examples retain their species, moisture or manufacturer basis. Sources are not fetched when you use the calculator.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • OpenStax Precalculus 2e, 5.1 Angles: radian measure and arc lengthhttps://openstax.org/books/precalculus-2e/pages/5-1-angles
  • NIST SP 811, Appendix B.9: mass, length, area and volume conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9