Wood CalculatorMeasure, plan & work with wood

Wood calculators / Volume, mass & moisture

Measure the wood. State the basis.

Wood Dimensional Change Calculator

Calculate approximate free-piece movement with a supplied directional coefficient in the cited 6–14% MC range.

Your wood & project inputs

mm
%
%
% dimension / MC point
%

Starting values are calculation examples. Verify actual dimensions, moisture basis, rates and model assumptions. Dimension-unit switching does not change fixed-unit price or engineering-property inputs.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Signed change = initial dimension × decimal DCC × (final MC − initial MC).

Calculate approximate free-piece movement with a supplied directional coefficient in the cited 6–14% MC range.

  1. Confirm the physical, product or tally basis and use the stated units.
  2. Enter actual measurements and justified properties, prices or project allowances.
  3. Submit the form, then interpret the result with the assumptions and limits below.

The initial 0.245% per MC point is the USDA worked white-fir tangential example, not a coefficient for every wood or grain direction. This does not select an installed-floor expansion gap.

Wood Dimensional Change: formula, units and interpretation

Calculate approximate free-piece movement with a supplied directional coefficient in the cited 6–14% MC range. The initial 0.245% per MC point is the USDA worked white-fir tangential example, not a coefficient for every wood or grain direction. This does not select an installed-floor expansion gap.

Separate the measured physical quantity from the purchase or design convention. Nominal lumber names, finished dimensions, geometric board feet, log-rule yield, stacked cords and mass describe different things. The method on this page uses only the basis stated beside its inputs; do not replace a missing property with an unrelated unit or trade name.

Before using the answer for a real project, confirm measurements and the relevant supplier information. Entered waste, prices, material properties and limits remain user choices. A rounded purchasing count is a quantity allowance rather than a cutting plan, and a calculated physical response is not a building-code approval.

Check the numbers

Wood Dimensional Change Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not stock recommendations, current quotes, code design values or full standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Initial across-grain dimension = 200 mm; Initial dry-basis MC = 12 %; Final dry-basis MC = 8 %; Chosen dimensional change coefficient = 0.245 % dimension / MC point; Upper validated MC bound = 14 %.

OutputComputed result
Signed dimensional change-1.96 mm
Initial dimension200 mm
Estimated final dimension198.04 mm
Change in inches-0.077165 in

How the stated input changes the result

ScenarioChanged input / basisResult
100 mmInitial across-grain dimension-0.98 mm
150 mmInitial across-grain dimension-1.47 mm
200 mmInitial across-grain dimension-1.96 mm
250 mmInitial across-grain dimension-2.45 mm
300 mmInitial across-grain dimension-2.94 mm
400 mmInitial across-grain dimension-3.92 mm

Unchanged inputs use: Dimension units = Metric (m / mm); Initial across-grain dimension = 200 mm; Initial dry-basis MC = 12 %; Final dry-basis MC = 8 %; Chosen dimensional change coefficient = 0.245 % dimension / MC point; Upper validated MC bound = 14 %. Results retain the model limitations described above.

Common questions

What is the coefficient basis?

USDA’s worked white-fir tangential DCC is 0.00245 as a decimal per MC point, entered here as 0.245 percent per MC point.

Can I enter green-wood moisture?

No. This cited approximation is restricted to 6–14% MC; it is not a full green-to-oven-dry model.

Does negative change mean shrinkage?

Yes. A lower final MC gives a negative dimensional change under the stated model.

Does it set flooring clearance?

No. Installed systems involve restraint, profiles, manufacturer instructions and environmental conditions.

How do I use this wood dimensional change calculator?

Calculate approximate free-piece movement with a supplied directional coefficient in the cited 6–14% MC range. Signed change = initial dimension × decimal DCC × (final MC − initial MC). Read the dimensioned examples below before entering project values.

Do starting values represent product or code recommendations?

No. They are stated calculation examples. Verify actual dimensions, material or product properties, units and site conditions. Neither a positive result nor an example value establishes a certified product, allowed load, compliant layout or current market price.

Can I export the result to Excel?

After calculating, use Export CSV. Excel can open the numeric results and submitted inputs. This is a text export, not a native formula workbook, desktop app or downloadable design package.

Where do the formulas and data come from?

Method and material references are listed below as plain-text addresses. Dimensional tables are calculated here from the stated inputs. Product density examples retain their species, moisture or manufacturer basis. Sources are not fetched when you use the calculator.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • USDA Wood Handbook, FPL-GTR-282, Chapter 13: moisture content and dimensional change, equation 13-3https://research.fs.usda.gov/download/treesearch/62261.pdf
  • Oklahoma State University Extension: Dimensional Changes in Woodhttps://extension.okstate.edu/fact-sheets/dimensional-changes-in-wood