Wood CalculatorMeasure, plan & work with wood

Wood calculators / Volume, mass & moisture

Measure the wood. State the basis.

Wood Moisture Content Calculator

Calculate oven-dry-basis moisture content from measured wet and oven-dry masses.

Your wood & project inputs

kg
kg

Starting values are calculation examples. Verify actual dimensions, moisture basis, rates and model assumptions. Dimension-unit switching does not change fixed-unit price or engineering-property inputs.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Dry-basis MC = (wet mass − oven-dry mass) / oven-dry mass × 100%.

Calculate oven-dry-basis moisture content from measured wet and oven-dry masses.

  1. Confirm the physical, product or tally basis and use the stated units.
  2. Enter actual measurements and justified properties, prices or project allowances.
  3. Submit the form, then interpret the result with the assumptions and limits below.

This is measurement arithmetic, not a moisture-meter calibration, kiln schedule or drying procedure.

Wood Moisture Content: formula, units and interpretation

Calculate oven-dry-basis moisture content from measured wet and oven-dry masses. This is measurement arithmetic, not a moisture-meter calibration, kiln schedule or drying procedure.

Separate the measured physical quantity from the purchase or design convention. Nominal lumber names, finished dimensions, geometric board feet, log-rule yield, stacked cords and mass describe different things. The method on this page uses only the basis stated beside its inputs; do not replace a missing property with an unrelated unit or trade name.

Before using the answer for a real project, confirm measurements and the relevant supplier information. Entered waste, prices, material properties and limits remain user choices. A rounded purchasing count is a quantity allowance rather than a cutting plan, and a calculated physical response is not a building-code approval.

Check the numbers

Wood Moisture Content Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not stock recommendations, current quotes, code design values or full standards tables.

Worked example with stated inputs

Initial wet mass = 1.2 kg; Oven-dry wood mass = 1 kg.

OutputComputed result
Oven-dry-basis moisture content20 % dry basis
Water mass0.2 kg
Wet-basis moisture16.666667 % wet basis

How the stated input changes the result

ScenarioChanged input / basisResult
1 kgInitial wet mass0 % dry basis
1.2 kgInitial wet mass20 % dry basis
1.4 kgInitial wet mass40 % dry basis
1.6 kgInitial wet mass60 % dry basis
1.8 kgInitial wet mass80 % dry basis
2 kgInitial wet mass100 % dry basis

Unchanged inputs use: Initial wet mass = 1.2 kg; Oven-dry wood mass = 1 kg. Results retain the model limitations described above.

Common questions

Can dry-basis moisture exceed 100 percent?

Yes. Water mass can exceed oven-dry wood mass.

Is dry basis the same as wet basis?

No. Wet basis divides water mass by total wet mass; dry basis divides by dry wood mass.

Does this tell me whether a board is ready for installation?

No. That requires the relevant product and environmental criteria.

How do I use this wood moisture content calculator?

Calculate oven-dry-basis moisture content from measured wet and oven-dry masses. Dry-basis MC = (wet mass − oven-dry mass) / oven-dry mass × 100%. Read the dimensioned examples below before entering project values.

Do starting values represent product or code recommendations?

No. They are stated calculation examples. Verify actual dimensions, material or product properties, units and site conditions. Neither a positive result nor an example value establishes a certified product, allowed load, compliant layout or current market price.

Can I export the result to Excel?

After calculating, use Export CSV. Excel can open the numeric results and submitted inputs. This is a text export, not a native formula workbook, desktop app or downloadable design package.

Where do the formulas and data come from?

Method and material references are listed below as plain-text addresses. Dimensional tables are calculated here from the stated inputs. Product density examples retain their species, moisture or manufacturer basis. Sources are not fetched when you use the calculator.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • USDA Wood Handbook, FPL-GTR-282, Chapter 13: moisture content and dimensional change, equation 13-3https://research.fs.usda.gov/download/treesearch/62261.pdf
  • USDA FPL-GTR-76: Specific Gravity, Moisture Content, and Density Relationship for Woodhttps://www.fpl.fs.usda.gov/documnts/fplgtr/fplgtr76.pdf