Wood CalculatorMeasure, plan & work with wood

Wood calculators / Logs & standing timber

Measure the wood. State the basis.

Wood Log Weight Calculator

Estimate log or tapered wood-pole self-mass using measured diameters and a supplied bulk density.

Your wood & project inputs

m
mm
mm
mm

Density references have a stated species/product and moisture basis. Any edited density must be appropriate for the actual piece.

kg/m³
pieces

Starting values are calculation examples. Verify actual dimensions, moisture basis, rates and model assumptions. Dimension-unit switching does not change fixed-unit price or engineering-property inputs.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Log mass = selected under-bark geometric volume × same-condition bulk density.

Estimate log or tapered wood-pole self-mass using measured diameters and a supplied bulk density.

  1. Confirm the physical, product or tally basis and use the stated units.
  2. Enter actual measurements and justified properties, prices or project allowances.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Bark, embedded material, decay, lifting dynamics and support capacity are excluded. Generic 500 kg/m³ is an illustration, not green-wood density.

Wood Log Weight: formula, units and interpretation

Estimate log or tapered wood-pole self-mass using measured diameters and a supplied bulk density. Bark, embedded material, decay, lifting dynamics and support capacity are excluded. Generic 500 kg/m³ is an illustration, not green-wood density.

Separate the measured physical quantity from the purchase or design convention. Nominal lumber names, finished dimensions, geometric board feet, log-rule yield, stacked cords and mass describe different things. The method on this page uses only the basis stated beside its inputs; do not replace a missing property with an unrelated unit or trade name.

Before using the answer for a real project, confirm measurements and the relevant supplier information. Entered waste, prices, material properties and limits remain user choices. A rounded purchasing count is a quantity allowance rather than a cutting plan, and a calculated physical response is not a building-code approval.

Check the numbers

Wood Log Weight Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not stock recommendations, current quotes, code design values or full standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Log length = 4 m; Small-end inside-bark diameter = 300 mm; Large-end inside-bark diameter = 400 mm; Midpoint inside-bark diameter = 350 mm; Volume model = Frustum; Density reference = Custom / measured density; Bulk density at stated moisture = 500 kg/m³; Quantity = 1 pieces.

OutputComputed result
Log mass at supplied bulk density193.731547 kg
Mass in pounds427.104951 lb
Quantity1 pieces
Total mass193.731547 kg
Solid volume0.387463 m³
Solid volume in cubic feet13.68313 ft³
Geometric board-foot equivalent164.19756 BF
Entered bulk density500 kg/m³
Density referenceCustom entered density
Reference basis; override may differUser-supplied same-condition density; no preset moisture condition

How the stated input changes the result

ScenarioChanged input / basisResult
2 mLog length96.865773 kg
3 mLog length145.29866 kg
4 mLog length193.731547 kg
5 mLog length242.164434 kg
6 mLog length290.59732 kg
8 mLog length387.463094 kg

Unchanged inputs use: Dimension units = Metric (m / mm); Log length = 4 m; Small-end inside-bark diameter = 300 mm; Large-end inside-bark diameter = 400 mm; Midpoint inside-bark diameter = 350 mm; Volume model = Frustum; Density reference = Custom / measured density; Bulk density at stated moisture = 500 kg/m³; Quantity = 1 pieces. Results retain the model limitations described above.

Common questions

Can I use this for a wooden pole?

Yes as a geometric mass estimate when the selected taper model and density describe it, excluding hardware and embedded material.

Does it include bark?

No. Diameters are inside bark; bark mass must be handled separately.

Is the weight valid for every moisture level?

No. Supply bulk density at the actual moisture and volume condition.

How do I use this wood log weight calculator?

Estimate log or tapered wood-pole self-mass using measured diameters and a supplied bulk density. Log mass = selected under-bark geometric volume × same-condition bulk density. Read the dimensioned examples below before entering project values.

Do starting values represent product or code recommendations?

No. They are stated calculation examples. Verify actual dimensions, material or product properties, units and site conditions. Neither a positive result nor an example value establishes a certified product, allowed load, compliant layout or current market price.

Can I export the result to Excel?

After calculating, use Export CSV. Excel can open the numeric results and submitted inputs. This is a text export, not a native formula workbook, desktop app or downloadable design package.

Where do the formulas and data come from?

Method and material references are listed below as plain-text addresses. Dimensional tables are calculated here from the stated inputs. Product density examples retain their species, moisture or manufacturer basis. Sources are not fetched when you use the calculator.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • USDA Forest Service, Freese, A Collection of Log Rules, FPL-01, Section II, printed pages 44-48: cubic volume formulaehttps://research.fs.usda.gov/download/treesearch/9829.pdf
  • USDA Wood Handbook, Chapter 4: dry-basis moisture content and specific-gravity/density definitionshttps://research.fs.usda.gov/download/treesearch/37428.pdf
  • NIST SP 811, Appendix B.9: mass, length, area and volume conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9