Wood CalculatorMeasure, plan & work with wood

Wood calculators / Logs & standing timber

Measure the wood. State the basis.

Newton Log Volume Calculator

Calculate under-bark geometric log volume with the explicitly selected newton measurement model.

Your wood & project inputs

m
mm
mm
mm

Starting values are calculation examples. Verify actual dimensions, moisture basis, rates and model assumptions. Dimension-unit switching does not change fixed-unit price or engineering-property inputs.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

V = length × (small-end area + 4 × midpoint area + large-end area)/6.

Calculate under-bark geometric log volume with the explicitly selected newton measurement model.

  1. Confirm the physical, product or tally basis and use the stated units.
  2. Enter actual measurements and justified properties, prices or project allowances.
  3. Submit the form, then interpret the result with the assumptions and limits below.

No bark allowance, defect deduction, merchantable recovery factor or local scaling convention is inferred.

Newton Log Volume: formula, units and interpretation

Calculate under-bark geometric log volume with the explicitly selected newton measurement model. No bark allowance, defect deduction, merchantable recovery factor or local scaling convention is inferred.

Separate the measured physical quantity from the purchase or design convention. Nominal lumber names, finished dimensions, geometric board feet, log-rule yield, stacked cords and mass describe different things. The method on this page uses only the basis stated beside its inputs; do not replace a missing property with an unrelated unit or trade name.

Before using the answer for a real project, confirm measurements and the relevant supplier information. Entered waste, prices, material properties and limits remain user choices. A rounded purchasing count is a quantity allowance rather than a cutting plan, and a calculated physical response is not a building-code approval.

Check the numbers

Newton Log Volume Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not stock recommendations, current quotes, code design values or full standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Under-bark log length = 4 m; Small-end inside-bark diameter = 300 mm; Large-end inside-bark diameter = 400 mm; Midpoint inside-bark diameter = 350 mm; Geometric model = Newton.

OutputComputed result
Under-bark geometric log volume0.387463 m³
Solid volume0.387463 m³
Solid volume in cubic feet13.68313 ft³
Geometric board-foot equivalent164.19756 BF
Selected volume modelnewton

How the stated input changes the result

ScenarioChanged input / basisResult
2 mUnder-bark log length0.193732 m³
3 mUnder-bark log length0.290597 m³
4 mUnder-bark log length0.387463 m³
5 mUnder-bark log length0.484329 m³
6 mUnder-bark log length0.581195 m³
8 mUnder-bark log length0.774926 m³

Unchanged inputs use: Dimension units = Metric (m / mm); Under-bark log length = 4 m; Small-end inside-bark diameter = 300 mm; Large-end inside-bark diameter = 400 mm; Midpoint inside-bark diameter = 350 mm; Geometric model = Newton. Results retain the model limitations described above.

Common questions

Are all three diameters used by this model?

Huber uses only the midpoint; Smalian uses the two ends; Newton uses all three; the conical-frustum model uses both ends. Unused displayed reference diameters do not affect the chosen method.

Does multiplying cubic feet by 12 give sawmill yield?

It gives only a geometric BF equivalent. A log rule estimates yield on another basis.

Can an irregular log match the geometric estimate?

Crook, ovality, butt swell, decay and changing taper can require a different measurement procedure.

How do I use this newton log volume calculator?

Calculate under-bark geometric log volume with the explicitly selected newton measurement model. V = length × (small-end area + 4 × midpoint area + large-end area)/6. Read the dimensioned examples below before entering project values.

Do starting values represent product or code recommendations?

No. They are stated calculation examples. Verify actual dimensions, material or product properties, units and site conditions. Neither a positive result nor an example value establishes a certified product, allowed load, compliant layout or current market price.

Can I export the result to Excel?

After calculating, use Export CSV. Excel can open the numeric results and submitted inputs. This is a text export, not a native formula workbook, desktop app or downloadable design package.

Where do the formulas and data come from?

Method and material references are listed below as plain-text addresses. Dimensional tables are calculated here from the stated inputs. Product density examples retain their species, moisture or manufacturer basis. Sources are not fetched when you use the calculator.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • USDA Forest Service, Freese, A Collection of Log Rules, FPL-01, Section II, printed pages 44-48: cubic volume formulaehttps://research.fs.usda.gov/download/treesearch/9829.pdf
  • NIST SP 811, Appendix B.9: mass, length, area and volume conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9