Wood CalculatorMeasure, plan & work with wood

Wood calculators / Surface materials & budgets

Measure the wood. State the basis.

Timber Cladding Board Calculator

Count straight courses and whole stock boards for the stated rectangular coverage and board dimensions.

Your wood & project inputs

m
m
mm
mm
m
%

Starting values are calculation examples. Verify actual dimensions, moisture basis, rates and model assumptions. Dimension-unit switching does not change fixed-unit price or engineering-property inputs.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Courses = ceil[(coverage width+gap)/(actual width+gap)]; pieces/course = ceil(run/stock length).

Count straight courses and whole stock boards for the stated rectangular coverage and board dimensions.

  1. Confirm the physical, product or tally basis and use the stated units.
  2. Enter actual measurements and justified properties, prices or project allowances.
  3. Submit the form, then interpret the result with the assumptions and limits below.

No diagonal layout, shared-offcut optimization, fastener, joint, framing or support design. The last edge may need ripping or a revised layout.

Timber Cladding Board: formula, units and interpretation

For profiled cladding, effective cover width can differ from the visible or overall board face. Enter the width that truly contributes to the repeated coverage, and do not count a tongue, overlap or hidden lap twice. This example is a straight-course quantity scenario, not a product-specific profile table.

Separate the measured physical quantity from the purchase or design convention. Nominal lumber names, finished dimensions, geometric board feet, log-rule yield, stacked cords and mass describe different things. The method on this page uses only the basis stated beside its inputs; do not replace a missing property with an unrelated unit or trade name.

Before using the answer for a real project, confirm measurements and the relevant supplier information. Entered waste, prices, material properties and limits remain user choices. A rounded purchasing count is a quantity allowance rather than a cutting plan, and a calculated physical response is not a building-code approval.

Check the numbers

Timber Cladding Board Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not stock recommendations, current quotes, code design values or full standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Surface / room length = 4 m; Surface / room width = 2 m; Actual face / board width = 95 mm; Chosen gap = 0 mm; Stock board length = 2.4 m; Chosen extra material allowance = 10 %.

OutputComputed result
Straight-course board allowance49 stock boards
Stock boards with reserve49 boards
Courses across width22 courses
Pieces per course2 pieces
Before reserve44 pieces
Full-course coverage2.09 m

How the stated input changes the result

ScenarioChanged input / basisResult
2 mSurface / room length25 stock boards
3 mSurface / room length49 stock boards
4 mSurface / room length49 stock boards
5 mSurface / room length73 stock boards
6 mSurface / room length73 stock boards
8 mSurface / room length97 stock boards

Unchanged inputs use: Dimension units = Metric (m / mm); Surface / room length = 4 m; Surface / room width = 2 m; Actual face / board width = 95 mm; Chosen gap = 0 mm; Stock board length = 2.4 m; Chosen extra material allowance = 10 %. Results retain the model limitations described above.

Common questions

Is cladding face width always its cover width?

No. For a profiled or lapped product, obtain the actual effective cover width and joint convention. This form does not derive it from a profile name.

Is the gap a universal installation requirement?

No. Enter the applicable product and project choice.

Can offcuts be reused automatically?

Not in this simple per-course count. Use the cut-list tool for a separate stock-cut scenario.

Does a deck board count design the deck frame?

No. Member capacity, foundations, connections and restraints are separate.

How do I use this timber cladding board calculator?

Count straight courses and whole stock boards for the stated rectangular coverage and board dimensions. Courses = ceil[(coverage width+gap)/(actual width+gap)]; pieces/course = ceil(run/stock length). Read the dimensioned examples below before entering project values.

Do starting values represent product or code recommendations?

No. They are stated calculation examples. Verify actual dimensions, material or product properties, units and site conditions. Neither a positive result nor an example value establishes a certified product, allowed load, compliant layout or current market price.

Can I export the result to Excel?

After calculating, use Export CSV. Excel can open the numeric results and submitted inputs. This is a text export, not a native formula workbook, desktop app or downloadable design package.

Where do the formulas and data come from?

Method and material references are listed below as plain-text addresses. Dimensional tables are calculated here from the stated inputs. Product density examples retain their species, moisture or manufacturer basis. Sources are not fetched when you use the calculator.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • Trex: How Many Deck Boards Do I Need? quantity method, not structural designhttps://www.trex.com/deck-ideas/how-many-deck-boards-do-i-need-/
  • NIST SP 811, Appendix B.9: mass, length, area and volume conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9