Wood CalculatorMeasure, plan & work with wood

Wood calculators / Logs & standing timber

Measure the wood. State the basis.

Standing Timber Volume Estimate Calculator

Evaluate a simple reference-area, height and user-supplied form-factor stem-volume scenario.

Your wood & project inputs

mm
m
ratio

Starting values are calculation examples. Verify actual dimensions, moisture basis, rates and model assumptions. Dimension-unit switching does not change fixed-unit price or engineering-property inputs.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Stem volume estimate = reference basal area × chosen height × supplied form factor.

Evaluate a simple reference-area, height and user-supplied form-factor stem-volume scenario.

  1. Confirm the physical, product or tally basis and use the stated units.
  2. Enter actual measurements and justified properties, prices or project allowances.
  3. Submit the form, then interpret the result with the assumptions and limits below.

The example form factor is not a species equation or inventory standard. No tree-specific taper, merchantability, defects or sawlog recovery are predicted.

Standing Timber Volume Estimate: formula, units and interpretation

Evaluate a simple reference-area, height and user-supplied form-factor stem-volume scenario. The example form factor is not a species equation or inventory standard. No tree-specific taper, merchantability, defects or sawlog recovery are predicted.

Separate the measured physical quantity from the purchase or design convention. Nominal lumber names, finished dimensions, geometric board feet, log-rule yield, stacked cords and mass describe different things. The method on this page uses only the basis stated beside its inputs; do not replace a missing property with an unrelated unit or trade name.

Before using the answer for a real project, confirm measurements and the relevant supplier information. Entered waste, prices, material properties and limits remain user choices. A rounded purchasing count is a quantity allowance rather than a cutting plan, and a calculated physical response is not a building-code approval.

Check the numbers

Standing Timber Volume Estimate Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not stock recommendations, current quotes, code design values or full standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Reference stem / DBH diameter = 300 mm; Chosen merchantable height = 15 m; User-supplied form factor = 0.5 ratio.

OutputComputed result
User-factor standing stem volume0.530144 m³
Solid volume0.530144 m³
Solid volume in cubic feet18.72185 ft³
Geometric board-foot equivalent224.662203 BF

How the stated input changes the result

ScenarioChanged input / basisResult
150 mmReference stem / DBH diameter0.132536 m³
225 mmReference stem / DBH diameter0.298206 m³
300 mmReference stem / DBH diameter0.530144 m³
375 mmReference stem / DBH diameter0.82835 m³
450 mmReference stem / DBH diameter1.192823 m³
600 mmReference stem / DBH diameter2.120575 m³

Unchanged inputs use: Dimension units = Metric (m / mm); Reference stem / DBH diameter = 300 mm; Chosen merchantable height = 15 m; User-supplied form factor = 0.5 ratio. Results retain the model limitations described above.

Common questions

Can DBH alone determine board feet?

No. Height, taper, species, merchantability and a valid scaling procedure matter.

Is the form factor automatically chosen?

No. It must be supplied and justified; the starting value is illustrative.

Can the result be used as stumpage value?

Only as one hypothetical volume input; prices, scaling conventions and costs are separate.

How do I use this standing timber volume estimate calculator?

Evaluate a simple reference-area, height and user-supplied form-factor stem-volume scenario. Stem volume estimate = reference basal area × chosen height × supplied form factor. Read the dimensioned examples below before entering project values.

Do starting values represent product or code recommendations?

No. They are stated calculation examples. Verify actual dimensions, material or product properties, units and site conditions. Neither a positive result nor an example value establishes a certified product, allowed load, compliant layout or current market price.

Can I export the result to Excel?

After calculating, use Export CSV. Excel can open the numeric results and submitted inputs. This is a text export, not a native formula workbook, desktop app or downloadable design package.

Where do the formulas and data come from?

Method and material references are listed below as plain-text addresses. Dimensional tables are calculated here from the stated inputs. Product density examples retain their species, moisture or manufacturer basis. Sources are not fetched when you use the calculator.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • USDA Forest Service, Freese, A Collection of Log Rules, FPL-01, Section II, printed pages 44-48: cubic volume formulaehttps://research.fs.usda.gov/download/treesearch/9829.pdf
  • Purdue Extension FNR-191, Log and Tree Scaling Techniques, printed pages 1-2: Doyle, Scribner approximation, International quarter-inchhttps://www.extension.purdue.edu/extmedia/fnr/fnr-191.pdf
  • NIST SP 811, Appendix B.9: mass, length, area and volume conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9