Wood CalculatorMeasure, plan & work with wood

Wood calculators / Logs & standing timber

Measure the wood. State the basis.

Scribner Approximation Calculator

Calculate a source-defined log-rule yield estimate, distinct from geometric solid wood volume.

Your wood & project inputs

mm
m

Starting values are calculation examples. Verify actual dimensions, moisture basis, rates and model assumptions. Dimension-unit switching does not change fixed-unit price or engineering-property inputs.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Approximate Scribner BF = (0.79D² − 2D − 4) × L/16.

Calculate a source-defined log-rule yield estimate, distinct from geometric solid wood volume.

  1. Confirm the physical, product or tally basis and use the stated units.
  2. Enter actual measurements and justified properties, prices or project allowances.
  3. Submit the form, then interpret the result with the assumptions and limits below.

No defects, contract rounding conventions or guaranteed mill recovery. Scribner is a formula approximation for D<28 in and L≤16 ft; International supports only 4, 8, 12, 16 or 20 ft.

Scribner Approximation: formula, units and interpretation

Calculate a source-defined log-rule yield estimate, distinct from geometric solid wood volume. No defects, contract rounding conventions or guaranteed mill recovery. Scribner is a formula approximation for D<28 in and L≤16 ft; International supports only 4, 8, 12, 16 or 20 ft.

Separate the measured physical quantity from the purchase or design convention. Nominal lumber names, finished dimensions, geometric board feet, log-rule yield, stacked cords and mass describe different things. The method on this page uses only the basis stated beside its inputs; do not replace a missing property with an unrelated unit or trade name.

Before using the answer for a real project, confirm measurements and the relevant supplier information. Entered waste, prices, material properties and limits remain user choices. A rounded purchasing count is a quantity allowance rather than a cutting plan, and a calculated physical response is not a building-code approval.

Check the numbers

Scribner Approximation Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not stock recommendations, current quotes, code design values or full standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Small-end diameter inside bark = 406.4 mm; Scaling log length = 4.8768 m; Scaling rule = Scribner.

OutputComputed result
Log-rule yield estimate166.24 rule BF
Log rulescribner
Small-end diameter under bark16 in
Scaling length16 ft

How the stated input changes the result

ScenarioChanged input / basisResult
304.8 mmSmall-end diameter inside bark85.76 rule BF
355.6 mmSmall-end diameter inside bark122.84 rule BF
406.4 mmSmall-end diameter inside bark166.24 rule BF
457.2 mmSmall-end diameter inside bark215.96 rule BF
508 mmSmall-end diameter inside bark272 rule BF
609.6 mmSmall-end diameter inside bark403.04 rule BF

Unchanged inputs use: Dimension units = Metric (m / mm); Small-end diameter inside bark = 406.4 mm; Scaling log length = 4.8768 m; Scaling rule = Scribner. Results retain the model limitations described above.

Common questions

Is rule BF a direct cubic-volume conversion?

No. Scaling rules estimate lumber yield under their own assumptions.

Can this give standing-tree yield from DBH alone?

No. A log scaling diameter is a small-end inside-bark diameter, not automatically breast-height diameter.

Does Scribner mean an exact Decimal C lookup?

No. This is the explicitly cited algebraic approximation, not a copied Decimal C table.

Can International accept any log length?

No. Only the five cited length-specific coefficient sets are provided; arbitrary lengths are rejected.

How do I use this scribner approximation calculator?

Calculate a source-defined log-rule yield estimate, distinct from geometric solid wood volume. Approximate Scribner BF = (0.79D² − 2D − 4) × L/16. Read the dimensioned examples below before entering project values.

Do starting values represent product or code recommendations?

No. They are stated calculation examples. Verify actual dimensions, material or product properties, units and site conditions. Neither a positive result nor an example value establishes a certified product, allowed load, compliant layout or current market price.

Can I export the result to Excel?

After calculating, use Export CSV. Excel can open the numeric results and submitted inputs. This is a text export, not a native formula workbook, desktop app or downloadable design package.

Where do the formulas and data come from?

Method and material references are listed below as plain-text addresses. Dimensional tables are calculated here from the stated inputs. Product density examples retain their species, moisture or manufacturer basis. Sources are not fetched when you use the calculator.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • Purdue Extension FNR-191, Log and Tree Scaling Techniques, printed pages 1-2: Doyle, Scribner approximation, International quarter-inchhttps://www.extension.purdue.edu/extmedia/fnr/fnr-191.pdf
  • NIST SP 811, Appendix B.9: mass, length, area and volume conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9