Wood CalculatorMeasure, plan & work with wood

Wood calculators / Fences & framing

Measure the wood. State the basis.

Roof Rafter Geometry Calculator

Calculate a symmetric roof’s ideal common-rafter triangle length, rise and pitch angle.

Your wood & project inputs

m
in/12

Starting values are calculation examples. Verify actual dimensions, moisture basis, rates and model assumptions. Dimension-unit switching does not change fixed-unit price or engineering-property inputs.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Common-rafter ideal length = half span × √(1+(pitch/12)²).

Calculate a symmetric roof’s ideal common-rafter triangle length, rise and pitch angle.

  1. Confirm the physical, product or tally basis and use the stated units.
  2. Enter actual measurements and justified properties, prices or project allowances.
  3. Submit the form, then interpret the result with the assumptions and limits below.

No ridge thickness, overhang, seat/plumb cut allowance, structural sizing, truss or snow/wind design.

Roof Rafter Geometry: formula, units and interpretation

Calculate a symmetric roof’s ideal common-rafter triangle length, rise and pitch angle. No ridge thickness, overhang, seat/plumb cut allowance, structural sizing, truss or snow/wind design.

Separate the measured physical quantity from the purchase or design convention. Nominal lumber names, finished dimensions, geometric board feet, log-rule yield, stacked cords and mass describe different things. The method on this page uses only the basis stated beside its inputs; do not replace a missing property with an unrelated unit or trade name.

Before using the answer for a real project, confirm measurements and the relevant supplier information. Entered waste, prices, material properties and limits remain user choices. A rounded purchasing count is a quantity allowance rather than a cutting plan, and a calculated physical response is not a building-code approval.

Check the numbers

Roof Rafter Geometry Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not stock recommendations, current quotes, code design values or full standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Full symmetric roof span = 6 m; Rise per 12 horizontal run = 6 in/12.

OutputComputed result
Ideal common-rafter triangle length3.354102 m
Pitch angle26.565051 degrees
Ridge rise above plate1.5 m

How the stated input changes the result

ScenarioChanged input / basisResult
3 mFull symmetric roof span1.677051 m
4.5 mFull symmetric roof span2.515576 m
6 mFull symmetric roof span3.354102 m
7.5 mFull symmetric roof span4.192627 m
9 mFull symmetric roof span5.031153 m
12 mFull symmetric roof span6.708204 m

Unchanged inputs use: Dimension units = Metric (m / mm); Full symmetric roof span = 6 m; Rise per 12 horizontal run = 6 in/12. Results retain the model limitations described above.

Common questions

Is this the final cut length?

No. The ideal triangle excludes real ridge, eave and bearing details.

Does it size roof timber?

No. It calculates geometry only.

Does it design a roof truss?

No. Web layout, joint forces and connections are not implemented.

How do I use this roof rafter geometry calculator?

Calculate a symmetric roof’s ideal common-rafter triangle length, rise and pitch angle. Common-rafter ideal length = half span × √(1+(pitch/12)²). Read the dimensioned examples below before entering project values.

Do starting values represent product or code recommendations?

No. They are stated calculation examples. Verify actual dimensions, material or product properties, units and site conditions. Neither a positive result nor an example value establishes a certified product, allowed load, compliant layout or current market price.

Can I export the result to Excel?

After calculating, use Export CSV. Excel can open the numeric results and submitted inputs. This is a text export, not a native formula workbook, desktop app or downloadable design package.

Where do the formulas and data come from?

Method and material references are listed below as plain-text addresses. Dimensional tables are calculated here from the stated inputs. Product density examples retain their species, moisture or manufacturer basis. Sources are not fetched when you use the calculator.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • NIST SP 811, Appendix B.9: mass, length, area and volume conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9
  • NIST PS 20-25 American Softwood Lumber Standard, section 2.16 and Table 3 (printed page 15)https://www.nist.gov/system/files/documents/2024/12/11/PS%2020-25%20Final.pdf