Wood CalculatorMeasure, plan & work with wood

Wood calculators / Surface materials & budgets

Measure the wood. State the basis.

Mixed Width Flooring Calculator

Estimate total strip run for a mixed-width floor using explicit shares of linear length.

Your wood & project inputs

m
m
%
mm
%
mm
%
mm
%

Starting values are calculation examples. Verify actual dimensions, moisture basis, rates and model assumptions. Dimension-unit switching does not change fixed-unit price or engineering-property inputs.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Weighted width = Σ(width × linear-run share); total run = ordered area/weighted width.

Estimate total strip run for a mixed-width floor using explicit shares of linear length.

  1. Confirm the physical, product or tally basis and use the stated units.
  2. Enter actual measurements and justified properties, prices or project allowances.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Shares are length shares, not board-count shares or area shares. No random-layout optimizer, joint staggering or pack mixing is performed.

Mixed Width Flooring: formula, units and interpretation

Estimate total strip run for a mixed-width floor using explicit shares of linear length. Shares are length shares, not board-count shares or area shares. No random-layout optimizer, joint staggering or pack mixing is performed.

Separate the measured physical quantity from the purchase or design convention. Nominal lumber names, finished dimensions, geometric board feet, log-rule yield, stacked cords and mass describe different things. The method on this page uses only the basis stated beside its inputs; do not replace a missing property with an unrelated unit or trade name.

Before using the answer for a real project, confirm measurements and the relevant supplier information. Entered waste, prices, material properties and limits remain user choices. A rounded purchasing count is a quantity allowance rather than a cutting plan, and a calculated physical response is not a building-code approval.

Check the numbers

Mixed Width Flooring Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not stock recommendations, current quotes, code design values or full standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Surface / room length = 5 m; Surface / room width = 4 m; Chosen extra material allowance = 10 %; First strip width = 75 mm; First share of total linear run = 30 %; Second strip width = 100 mm; Second share of total linear run = 40 %; Third strip width = 150 mm; Third share of total linear run = 30 %.

OutputComputed result
Total strip run at supplied length shares204.651163 linear m
First-width run61.395349 m
Second-width run81.860465 m
Third-width run61.395349 m
Equivalent linear feet671.427699 ft

How the stated input changes the result

ScenarioChanged input / basisResult
2.5 mSurface / room length102.325581 linear m
3.75 mSurface / room length153.488372 linear m
5 mSurface / room length204.651163 linear m
6.25 mSurface / room length255.813953 linear m
7.5 mSurface / room length306.976744 linear m
10 mSurface / room length409.302326 linear m

Unchanged inputs use: Dimension units = Metric (m / mm); Surface / room length = 5 m; Surface / room width = 4 m; Chosen extra material allowance = 10 %; First strip width = 75 mm; First share of total linear run = 30 %; Second strip width = 100 mm; Second share of total linear run = 40 %; Third strip width = 150 mm; Third share of total linear run = 30 %. Results retain the model limitations described above.

Common questions

Must the three shares total 100 percent?

Yes. They divide the total linear run between the three chosen widths.

Are these board-count percentages?

No. Unequal piece lengths would make count shares different.

Does it create a random-width installation drawing?

No. It estimates material run at the stated mixture.

How do I use this mixed width flooring calculator?

Estimate total strip run for a mixed-width floor using explicit shares of linear length. Weighted width = Σ(width × linear-run share); total run = ordered area/weighted width. Read the dimensioned examples below before entering project values.

Do starting values represent product or code recommendations?

No. They are stated calculation examples. Verify actual dimensions, material or product properties, units and site conditions. Neither a positive result nor an example value establishes a certified product, allowed load, compliant layout or current market price.

Can I export the result to Excel?

After calculating, use Export CSV. Excel can open the numeric results and submitted inputs. This is a text export, not a native formula workbook, desktop app or downloadable design package.

Where do the formulas and data come from?

Method and material references are listed below as plain-text addresses. Dimensional tables are calculated here from the stated inputs. Product density examples retain their species, moisture or manufacturer basis. Sources are not fetched when you use the calculator.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • Lowe's: Wood Flooring Calculators, area and selected product coveragehttps://www.lowes.com/n/calculators/wood-flooring-calculator
  • NIST SP 811, Appendix B.9: mass, length, area and volume conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9