Wood calculators / Logs & standing timber
Measure the wood. State the basis.
International Quarter-Inch Log Rule Calculator
Calculate a source-defined log-rule yield estimate, distinct from geometric solid wood volume.
Your wood & project inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Use the cited length-specific quadratic in small-end diameter, then round to the nearest 5 rule BF.
Calculate a source-defined log-rule yield estimate, distinct from geometric solid wood volume.
- Confirm the physical, product or tally basis and use the stated units.
- Enter actual measurements and justified properties, prices or project allowances.
- Submit the form, then interpret the result with the assumptions and limits below.
No defects, contract rounding conventions or guaranteed mill recovery. Scribner is a formula approximation for D<28 in and L≤16 ft; International supports only 4, 8, 12, 16 or 20 ft.
International Quarter-Inch Log Rule: formula, units and interpretation
Calculate a source-defined log-rule yield estimate, distinct from geometric solid wood volume. No defects, contract rounding conventions or guaranteed mill recovery. Scribner is a formula approximation for D<28 in and L≤16 ft; International supports only 4, 8, 12, 16 or 20 ft.
Separate the measured physical quantity from the purchase or design convention. Nominal lumber names, finished dimensions, geometric board feet, log-rule yield, stacked cords and mass describe different things. The method on this page uses only the basis stated beside its inputs; do not replace a missing property with an unrelated unit or trade name.
Before using the answer for a real project, confirm measurements and the relevant supplier information. Entered waste, prices, material properties and limits remain user choices. A rounded purchasing count is a quantity allowance rather than a cutting plan, and a calculated physical response is not a building-code approval.
Continue with: Smalian Log Volume Calculator · Huber Log Volume Calculator · Newton Log Volume Calculator · Tapered Log Volume Calculator
Check the numbers
International Quarter-Inch Log Rule Calculator: calculated examples
These scenarios are computed with the same method as the form. They are not stock recommendations, current quotes, code design values or full standards tables.
Worked example with stated inputs
Dimension units = Metric (m / mm); Small-end diameter inside bark = 406.4 mm; Scaling log length = 4.8768 m; Scaling rule = International.
| Output | Computed result |
|---|---|
| Log-rule yield estimate | 180 rule BF |
| Log rule | international |
| Small-end diameter under bark | 16 in |
| Scaling length | 16 ft |
How the stated input changes the result
| Scenario | Changed input / basis | Result |
|---|---|---|
| 203.2 mm | Small-end diameter inside bark | 40 rule BF |
| 304.8 mm | Small-end diameter inside bark | 95 rule BF |
| 406.4 mm | Small-end diameter inside bark | 180 rule BF |
| 508 mm | Small-end diameter inside bark | 290 rule BF |
| 609.6 mm | Small-end diameter inside bark | 425 rule BF |
| 812.8 mm | Small-end diameter inside bark | 770 rule BF |
Unchanged inputs use: Dimension units = Metric (m / mm); Small-end diameter inside bark = 406.4 mm; Scaling log length = 4.8768 m; Scaling rule = International. Results retain the model limitations described above.
Common questions
Is rule BF a direct cubic-volume conversion?
No. Scaling rules estimate lumber yield under their own assumptions.
Can this give standing-tree yield from DBH alone?
No. A log scaling diameter is a small-end inside-bark diameter, not automatically breast-height diameter.
Does Scribner mean an exact Decimal C lookup?
No. This is the explicitly cited algebraic approximation, not a copied Decimal C table.
Can International accept any log length?
No. Only the five cited length-specific coefficient sets are provided; arbitrary lengths are rejected.
How do I use this international quarter-inch log rule calculator?
Calculate a source-defined log-rule yield estimate, distinct from geometric solid wood volume. Use the cited length-specific quadratic in small-end diameter, then round to the nearest 5 rule BF. Read the dimensioned examples below before entering project values.
Do starting values represent product or code recommendations?
No. They are stated calculation examples. Verify actual dimensions, material or product properties, units and site conditions. Neither a positive result nor an example value establishes a certified product, allowed load, compliant layout or current market price.
Can I export the result to Excel?
After calculating, use Export CSV. Excel can open the numeric results and submitted inputs. This is a text export, not a native formula workbook, desktop app or downloadable design package.
Where do the formulas and data come from?
Method and material references are listed below as plain-text addresses. Dimensional tables are calculated here from the stated inputs. Product density examples retain their species, moisture or manufacturer basis. Sources are not fetched when you use the calculator.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.
- Purdue Extension FNR-191, Log and Tree Scaling Techniques, printed pages 1-2: Doyle, Scribner approximation, International quarter-inchhttps://www.extension.purdue.edu/extmedia/fnr/fnr-191.pdf
- NIST SP 811, Appendix B.9: mass, length, area and volume conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9