Wood CalculatorMeasure, plan & work with wood

Wood calculators / Board feet & lumber

Measure the wood. State the basis.

Board Foot Volume Converter

Convert geometric board feet, MBF, cubic feet, cubic inches, cubic metres and cubic yards.

Your wood & project inputs

Starting values are calculation examples. Verify actual dimensions, moisture basis, rates and model assumptions. Dimension-unit switching does not change fixed-unit price or engineering-property inputs.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

1 geometric BF = 144 in³ = 1/12 ft³ = 0.002359737216 m³; 1 MBF = 1000 BF.

Convert geometric board feet, MBF, cubic feet, cubic inches, cubic metres and cubic yards.

  1. Confirm the physical, product or tally basis and use the stated units.
  2. Enter actual measurements and justified properties, prices or project allowances.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Volume units only. An inch or metre without a cubic exponent is a length, and log-rule BF is not solid-log volume.

Board Foot Volume Converter: formula, units and interpretation

Convert geometric board feet, MBF, cubic feet, cubic inches, cubic metres and cubic yards. Volume units only. An inch or metre without a cubic exponent is a length, and log-rule BF is not solid-log volume.

Separate the measured physical quantity from the purchase or design convention. Nominal lumber names, finished dimensions, geometric board feet, log-rule yield, stacked cords and mass describe different things. The method on this page uses only the basis stated beside its inputs; do not replace a missing property with an unrelated unit or trade name.

Before using the answer for a real project, confirm measurements and the relevant supplier information. Entered waste, prices, material properties and limits remain user choices. A rounded purchasing count is a quantity allowance rather than a cutting plan, and a calculated physical response is not a building-code approval.

Check the numbers

Board Foot Volume Converter: calculated examples

These scenarios are computed with the same method as the form. They are not stock recommendations, current quotes, code design values or full standards tables.

Worked example with stated inputs

Known volume = 1 ; Input unit = bf; Output unit = m3.

OutputComputed result
Same-volume unit conversion0.00236 m3
Solid volume0.00236 m³
Solid volume in cubic feet0.083333 ft³
Geometric board-foot equivalent1 BF

How the stated input changes the result

ScenarioChanged input / basisResult
0.5 Known volume0.00118 m3
0.75 Known volume0.00177 m3
1 Known volume0.00236 m3
1.25 Known volume0.00295 m3
1.5 Known volume0.00354 m3
2 Known volume0.004719 m3

Unchanged inputs use: Known volume = 1 ; Input unit = bf; Output unit = m3. Results retain the model limitations described above.

Common questions

Can I convert 650 board feet to cubic feet?

For geometric volume, divide by 12: 650 BF is 54.1666667 ft³. That arithmetic does not predict recovered lumber from a standing tree.

Does one cubic metre equal 423.776 board feet?

Approximately, for geometric volume units. The exact input factor used here is 0.002359737216 m³ per BF.

Can I convert board feet to inches or metres?

Only to cubic units without additional dimensions. A linear-length conversion also requires cross-sectional area.

How do I use this board foot volume converter?

Convert geometric board feet, MBF, cubic feet, cubic inches, cubic metres and cubic yards. 1 geometric BF = 144 in³ = 1/12 ft³ = 0.002359737216 m³; 1 MBF = 1000 BF. Read the dimensioned examples below before entering project values.

Do starting values represent product or code recommendations?

No. They are stated calculation examples. Verify actual dimensions, material or product properties, units and site conditions. Neither a positive result nor an example value establishes a certified product, allowed load, compliant layout or current market price.

Can I export the result to Excel?

After calculating, use Export CSV. Excel can open the numeric results and submitted inputs. This is a text export, not a native formula workbook, desktop app or downloadable design package.

Where do the formulas and data come from?

Method and material references are listed below as plain-text addresses. Dimensional tables are calculated here from the stated inputs. Product density examples retain their species, moisture or manufacturer basis. Sources are not fetched when you use the calculator.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • Penn State Extension, Valuing Standing Timber: board feet and MBFhttps://extension.psu.edu/valuing-standing-timber
  • NIST SP 811, Appendix B.9: mass, length, area and volume conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9