Wood calculators / Board feet & lumber
Measure the wood. State the basis.
Board Feet to Linear Feet Calculator
Find linear metres and feet for a board-foot volume at an explicitly stated thickness and width.
Your wood & project inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Linear length = board-foot geometric volume / actual cross-sectional area.
Find linear metres and feet for a board-foot volume at an explicitly stated thickness and width.
- Confirm the physical, product or tally basis and use the stated units.
- Enter actual measurements and justified properties, prices or project allowances.
- Submit the form, then interpret the result with the assumptions and limits below.
A fixed BF-to-linear-foot multiplier cannot apply to every cross-section.
Board Feet to Linear Feet: formula, units and interpretation
Find linear metres and feet for a board-foot volume at an explicitly stated thickness and width. A fixed BF-to-linear-foot multiplier cannot apply to every cross-section.
Separate the measured physical quantity from the purchase or design convention. Nominal lumber names, finished dimensions, geometric board feet, log-rule yield, stacked cords and mass describe different things. The method on this page uses only the basis stated beside its inputs; do not replace a missing property with an unrelated unit or trade name.
Before using the answer for a real project, confirm measurements and the relevant supplier information. Entered waste, prices, material properties and limits remain user choices. A rounded purchasing count is a quantity allowance rather than a cutting plan, and a calculated physical response is not a building-code approval.
Continue with: Board Foot Calculator · Board Foot Volume Converter · Board Feet to Square Feet Calculator · Board Feet to Pieces Calculator
Check the numbers
Board Feet to Linear Feet Calculator: calculated examples
These scenarios are computed with the same method as the form. They are not stock recommendations, current quotes, code design values or full standards tables.
Worked example with stated inputs
Dimension units = Metric (m / mm); Geometric board feet = 100 BF; Actual width = 152.4 mm; Actual thickness = 25.4 mm.
| Output | Computed result |
|---|---|
| Linear length at stated cross-section | 60.96 m |
| Linear feet | 200 ft |
| Net section area | 0.003871 m² |
How the stated input changes the result
| Scenario | Changed input / basis | Result |
|---|---|---|
| 50 BF | Geometric board feet | 30.48 m |
| 75 BF | Geometric board feet | 45.72 m |
| 100 BF | Geometric board feet | 60.96 m |
| 125 BF | Geometric board feet | 76.2 m |
| 150 BF | Geometric board feet | 91.44 m |
| 200 BF | Geometric board feet | 121.92 m |
Unchanged inputs use: Dimension units = Metric (m / mm); Geometric board feet = 100 BF; Actual width = 152.4 mm; Actual thickness = 25.4 mm. Results retain the model limitations described above.
Common questions
Why does width change linear feet?
The same total volume makes less length when the section is wider or thicker.
Is lineal foot different from linear foot?
They are commonly used for the same length measure in lumber quotations. Neither is a volume by itself.
Can I use nominal two-by-four sizes?
Only if nominal tally is your intended basis. For physical finished length from physical volume, enter actual measured dimensions.
How do I use this board feet to linear feet calculator?
Find linear metres and feet for a board-foot volume at an explicitly stated thickness and width. Linear length = board-foot geometric volume / actual cross-sectional area. Read the dimensioned examples below before entering project values.
Do starting values represent product or code recommendations?
No. They are stated calculation examples. Verify actual dimensions, material or product properties, units and site conditions. Neither a positive result nor an example value establishes a certified product, allowed load, compliant layout or current market price.
Can I export the result to Excel?
After calculating, use Export CSV. Excel can open the numeric results and submitted inputs. This is a text export, not a native formula workbook, desktop app or downloadable design package.
Where do the formulas and data come from?
Method and material references are listed below as plain-text addresses. Dimensional tables are calculated here from the stated inputs. Product density examples retain their species, moisture or manufacturer basis. Sources are not fetched when you use the calculator.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.
- Penn State Extension, Valuing Standing Timber: board feet and MBFhttps://extension.psu.edu/valuing-standing-timber
- NIST PS 20-25 American Softwood Lumber Standard, section 2.16 and Table 3 (printed page 15)https://www.nist.gov/system/files/documents/2024/12/11/PS%2020-25%20Final.pdf
- NIST SP 811, Appendix B.9: mass, length, area and volume conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9