Wood CalculatorMeasure, plan & work with wood

Wood calculators / Bounded elastic models

Measure the wood. State the basis.

Wood Beam Model Depth Bound Calculator

Evaluate the stated rectangular simple-beam elastic response or a model-only inverse bound.

Your wood & project inputs

mm
m
MPa
MPa
MPa
L/limit
kN/m

Starting values are calculation examples. Verify actual dimensions, moisture basis, rates and model assumptions. Dimension-unit switching does not change fixed-unit price or engineering-property inputs.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

I=bh³/12; S=bh²/6. Uniform: M=wL²/8, shear=wL/2, δ=5wL⁴/(384EI). Midpoint point load: M=PL/4, δ=PL³/(48EI). Inverse tools use only the stated uniform-load bending, shear and L/ratio bounds.

Evaluate the stated rectangular simple-beam elastic response or a model-only inverse bound.

  1. Confirm the physical, product or tally basis and use the stated units.
  2. Enter actual measurements and justified properties, prices or project allowances.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Ideal straight, simply supported, laterally restrained rectangular beam with the stated load. E, Fb and Fv are user-supplied scenario inputs, not assigned grade properties. No load combinations, duration/moisture/size factors, creep, bearing, lateral stability, notches, connections or NDS/Eurocode/regional compliance. These results are not safe working loads or stock-size recommendations.

Wood Beam Model Depth Bound: formula, units and interpretation

Evaluate the stated rectangular simple-beam elastic response or a model-only inverse bound. Ideal straight, simply supported, laterally restrained rectangular beam with the stated load. E, Fb and Fv are user-supplied scenario inputs, not assigned grade properties. No load combinations, duration/moisture/size factors, creep, bearing, lateral stability, notches, connections or NDS/Eurocode/regional compliance. These results are not safe working loads or stock-size recommendations.

Separate the measured physical quantity from the purchase or design convention. Nominal lumber names, finished dimensions, geometric board feet, log-rule yield, stacked cords and mass describe different things. The method on this page uses only the basis stated beside its inputs; do not replace a missing property with an unrelated unit or trade name.

Before using the answer for a real project, confirm measurements and the relevant supplier information. Entered waste, prices, material properties and limits remain user choices. A rounded purchasing count is a quantity allowance rather than a cutting plan, and a calculated physical response is not a building-code approval.

Check the numbers

Wood Beam Model Depth Bound Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not stock recommendations, current quotes, code design values or full standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Effective rectangular width = 100 mm; Simple support span = 3 m; User-supplied elastic modulus E = 10000 MPa; User-supplied bending reference stress = 8 MPa; User-supplied shear reference stress = 1 MPa; Chosen span/deflection ratio = 360 L/limit; Total service uniform load = 2 kN/m.

OutputComputed result
Model-only rectangular depth bound144.823408 mm
Bending-only depth129.903811 mm
Shear-only depth45 mm
Deflection-only depth144.823408 mm

How the stated input changes the result

ScenarioChanged input / basisResult
1.5 mSimple support span72.411704 mm
2.25 mSimple support span108.617556 mm
3 mSimple support span144.823408 mm
3.75 mSimple support span181.02926 mm
4.5 mSimple support span217.235112 mm
6 mSimple support span289.646815 mm

Unchanged inputs use: Dimension units = Metric (m / mm); Effective rectangular width = 100 mm; Simple support span = 3 m; User-supplied elastic modulus E = 10000 MPa; User-supplied bending reference stress = 8 MPa; User-supplied shear reference stress = 1 MPa; Chosen span/deflection ratio = 360 L/limit; Total service uniform load = 2 kN/m. Results retain the model limitations described above.

Common questions

Does this choose a safe code-compliant timber size?

No. It evaluates a limited elastic model with supplied inputs. A complete design needs the applicable standard, grade/product data, adjustment factors and all relevant checks.

Can I use it for LVL, glulam or I-joists?

Only if the model and supplied effective properties are applicable. Proprietary members and I-joists need manufacturer procedures; no brand span table is built in.

Does the load include member self-weight?

It must be included in your stated load if appropriate; the tool does not add it automatically.

Does it implement AWC connections, shear walls, diaphragm deflection or dowel strength?

No. The source identifies the simple-beam equations only. Fastener, shear-wall, truss, retaining-wall and connection models are not implemented.

How do I use this wood beam model depth bound calculator?

Evaluate the stated rectangular simple-beam elastic response or a model-only inverse bound. I=bh³/12; S=bh²/6. Uniform: M=wL²/8, shear=wL/2, δ=5wL⁴/(384EI). Midpoint point load: M=PL/4, δ=PL³/(48EI). Inverse tools use only the stated uniform-load bending, shear and L/ratio bounds. Read the dimensioned examples below before entering project values.

Do starting values represent product or code recommendations?

No. They are stated calculation examples. Verify actual dimensions, material or product properties, units and site conditions. Neither a positive result nor an example value establishes a certified product, allowed load, compliant layout or current market price.

Can I export the result to Excel?

After calculating, use Export CSV. Excel can open the numeric results and submitted inputs. This is a text export, not a native formula workbook, desktop app or downloadable design package.

Where do the formulas and data come from?

Method and material references are listed below as plain-text addresses. Dimensional tables are calculated here from the stated inputs. Product density examples retain their species, moisture or manufacturer basis. Sources are not fetched when you use the calculator.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • American Wood Council Design Aid No. 6, Beam Design Formulas: Figure 1 (uniform load), Figure 7 (midspan point load)https://awc.org/wp-content/uploads/2021/12/AWC-DA6-BeamFormulas-0710.pdf
  • USDA Wood Handbook 2021, Chapter 9: Table 9-1, equations 9-3, 9-4, 9-13, 9-14 and 9-25https://research.fs.usda.gov/download/treesearch/62251.pdf
  • NIST SP 811, Appendix B.9: mass, length, area and volume conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9