Wood CalculatorMeasure, plan & work with wood

Wood calculators / Panels & cutting

Measure the wood. State the basis.

Cutting Board Lumber Calculator

Sum a simple strip cutting-board blank and compare raw board-foot input with finished width after explicit edge trims.

Your wood & project inputs

m
mm
mm

Cut dimensions follow the selected mm / in units; counts stay whole numbers.

Starting values are calculation examples. Verify actual dimensions, moisture basis, rates and model assumptions. Dimension-unit switching does not change fixed-unit price or engineering-property inputs.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Raw width = sum(strip width × count); raw BF = length × raw width × thickness / geometric BF factor.

Sum a simple strip cutting-board blank and compare raw board-foot input with finished width after explicit edge trims.

  1. Confirm the physical, product or tally basis and use the stated units.
  2. Enter actual measurements and justified properties, prices or project allowances.
  3. Submit the form, then interpret the result with the assumptions and limits below.

No glue-line, flattening loss, crosscut kerf, end-grain reorientation, food-contact suitability or manufacturing process is inferred.

Cutting Board Lumber: formula, units and interpretation

Sum a simple strip cutting-board blank and compare raw board-foot input with finished width after explicit edge trims. No glue-line, flattening loss, crosscut kerf, end-grain reorientation, food-contact suitability or manufacturing process is inferred.

Separate the measured physical quantity from the purchase or design convention. Nominal lumber names, finished dimensions, geometric board feet, log-rule yield, stacked cords and mass describe different things. The method on this page uses only the basis stated beside its inputs; do not replace a missing property with an unrelated unit or trade name.

Before using the answer for a real project, confirm measurements and the relevant supplier information. Entered waste, prices, material properties and limits remain user choices. A rounded purchasing count is a quantity allowance rather than a cutting plan, and a calculated physical response is not a building-code approval.

Check the numbers

Cutting Board Lumber Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not stock recommendations, current quotes, code design values or full standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Raw strip length = 0.5 m; Uniform strip thickness = 25 mm; Trim off each assembled width edge = 5 mm; Strip list: width, quantity (one per line) = 40,5 30,4.

OutputComputed result
Raw strip geometric board feet1.695104 BF
Raw blank width320 mm
Finished width after edge trim310 mm
Finished geometric volume0.003875 m³
Strip count9 strips

How the stated input changes the result

ScenarioChanged input / basisResult
0.25 mRaw strip length0.847552 BF
0.375 mRaw strip length1.271328 BF
0.5 mRaw strip length1.695104 BF
0.625 mRaw strip length2.11888 BF
0.75 mRaw strip length2.542656 BF
1 mRaw strip length3.390208 BF

Unchanged inputs use: Dimension units = Metric (m / mm); Raw strip length = 0.5 m; Uniform strip thickness = 25 mm; Trim off each assembled width edge = 5 mm; Strip list: width, quantity (one per line) = 40,5 30,4. Results retain the model limitations described above.

Common questions

Does the strip list include glue gaps?

No. It sums the stated wood strip widths as a simple blank.

Does it plan an end-grain cutting board?

No. Re-sawing and reorientation require a separately determined part list and process.

Does raw BF equal finished BF?

Not if you trim or plane material. This form shows the explicit width trimming only.

How do I use this cutting board lumber calculator?

Sum a simple strip cutting-board blank and compare raw board-foot input with finished width after explicit edge trims. Raw width = sum(strip width × count); raw BF = length × raw width × thickness / geometric BF factor. Read the dimensioned examples below before entering project values.

Do starting values represent product or code recommendations?

No. They are stated calculation examples. Verify actual dimensions, material or product properties, units and site conditions. Neither a positive result nor an example value establishes a certified product, allowed load, compliant layout or current market price.

Can I export the result to Excel?

After calculating, use Export CSV. Excel can open the numeric results and submitted inputs. This is a text export, not a native formula workbook, desktop app or downloadable design package.

Where do the formulas and data come from?

Method and material references are listed below as plain-text addresses. Dimensional tables are calculated here from the stated inputs. Product density examples retain their species, moisture or manufacturer basis. Sources are not fetched when you use the calculator.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • Penn State Extension, Valuing Standing Timber: board feet and MBFhttps://extension.psu.edu/valuing-standing-timber
  • NIST SP 811, Appendix B.9: mass, length, area and volume conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9